Remote-processing RPC-150 Manuale Utente

RPC-150 USER'S MANUALRPC-150 Page iCopyr ight 1993 - Remote Processing Corporation. Allrights reserved. However, any part of this documentmay

SAVING PROGRAMS CHAPTER 3Page 8 RPC-150Figure 3-1 Autorun jumperINTRODUCTIONPrograms are stored in socket U3. An optional real timeclock module, a D

CHAPTER 3 SAVING PROGRAMSRPC-150 Page 9especially true if the program has been configured toignore the < ESC> key. To prevent autorun, remov

SERIAL PORTS CHAPTER 4Page 10 RPC-150Figure 4-1 Serial portsDESCRIPTIONThe RPC -150 has two serial ports that can be used forinterfacing to a printer,

CHAPTER 4 SERIAL PORTSRPC-150 Page 11In this mode, you have access to the full 256 bytes. If you don' t read the buffer and the buffer fills, a

DATA MEMORY CHAPTER 5Page 12 RPC-150Figure 5-1 Data memoryINTRODUCTIONThe RP C-150 is available with 32 of RAM . RAM is insocket U1. RA M may be bat

CHAPTER 5 DATA MEMORYRPC-150 Page 1350 B = PEEK(60000)You can store and retrieve arrays, strings, and variablesin this way. There ar e many variatio

DIGITAL LINES CHAPTER 6Page 14 RPC-150Figure 6-1 Digital I/OINTRODUCTIONDigital I/O lines ar e used to inter face with opto-moduleracks, switches, low

CHAPTER 6 DIGITAL LINESRPC-150 Page 15Figure 6-2 Inductive load protectionThe output driver chip, U 13, can be replaced with a DIPshunt jumper so it i

DIGITAL LINES CHAPTER 6Page 16 RPC-150The logic at J2 port B, with the high current outputsinstalled is just the reverse. A ' 1' at a lin

CHAPTER 6 DIGITAL LINESRPC-150 Page 17Figure 6-3 Digital I/O connector pin out (viewed from top)Conne ctor pin ou t - J3Pin # 82C55 Description OptoPo

TABLE OF CONTENTSPage ii RPC-150Chapter 1 OverviewDESCRIPTION ... 1MANUAL ORGANIZATION ... 1MANUAL CONVENTIONS ...

CALENDAR/CLOCK CHAPTER 7Page 18 RPC-150Figure 7-1 Calendar/clock ins tallationDESCRIPTIONThe RPC-150 has a battery backed Calendar/clockoption using t

CHAPTER 8 KEYPAD PORTRPC-150 Page 19Figure 9-1 Keypad connectorINTRODUCTION16 position keypads are plugged into keypad port J5. Keys are arranged in a

KEYPAD PORT CHAPTER 8Page 20 RPC-150COMMANDSThe following is a list of CAMBASIC commands for thekeypad.Command FunctionINPUT KEYPAD$ Input data from a

CHAPTER 9 SPEAKERRPC-150 Page 21Figure 9-1 Speaker pin locationFigure 9-2 Interface schematicDESCRIPTIONPin 16 on the card edge connector is the spea

TECHNICAL INFORMATIONPage 22 RPC-150ELECTRICALCPU64180, 9.216 Mhz clockMemoryCAMBASIC, 32K ROMProgramming and data is 32K RAMProgram is 32K EPROM (U

TECHNICAL INFORMATIONRPC-150 Page 23Edge connectorLine Signal DescriptionA +5 PowerB D0 Data 0C D2 Data 2D D4 Data 4E D6 Data 6F A0 Address A0H A2 Add

TECHNICAL INFORMATIONPage 24 RPC-150RPC-150 board outline

CHAPTER 1 OVERVIEWRPC-150 Page 1DESCRIPTIONThe RP C-150 is an embedded contr oller with a built inBasic language. Several features make it suitable

OVERVIEW CHAPTER 1Page 2 RPC-150Figure 1-1 System layoutTECHNICAL SUPPORTIf you have a question about the RPC-150 orCAM BASIC used on it and can'

CHAPTER 2 SETUP AND OPERATIONRPC-150 Page 3Figure 2-1 RPC-150 Connector LayoutINTRODUCTIONThe RPC -150 is ready to program as soon as youconnect it to

SETUP AND OPERATION CHAPTER 2Page 4 RPC-150FIRST TIME OPERATIONBecome familiar with the locations of the connectorsbefore getting started. See Figure

CHAPTER 2 SETUP AND OPERATIONRPC-150 Page 54. Press < F2> to return to the immediate mode.NOTE: Some versions of P C SmartLINK have pulldown me

SETUP AND OPERATION CHAPTER 2Page 6 RPC-150downloaded file. For example, you could have thefollowing in a file written on your editor:'Check tem

CHAPTER 2 SETUP AND OPERATIONRPC-150 Page 7TROUBLESHOOTINGYou probably turned to this section because you couldnot get the sign on message. If you ar